1 Now the first step to make u pipe solar collector, minimize a sheet of 4-by-8-by-1/2 inch plywood to 3 foot 3inches by 8 foot with a round saw.
2 Minimize a 2-by-4-by-8 foot stud into two 3 foot lengths.
3 Fasten two 2-by-4-by-8 studs flush with possibly 8-foot borders of the sheet of plywood. Fasten the two 2-by-4-by-3 studs flush with the best and bottom borders of the sheet of plywood with 1 1/2 inch drywall screws. Generate the screws via the back again of the plywood into the studs. Fasten the 3 foot studs to the 8 foot studs by toe toenailing the ends of the studs collectively utilizing screws. To toe toenail two boards collectively, a toenail or screw should be driven at a steep angle via the facets of 1 board into the board that is perpendicular to it. Toe toenailing is utilized when a toenail or screw cannot be driven directly via the back again of 1 board into an additional.
4 Minimize 1 1-by-4-by-8 board lengthwise into identical widths.
5 Minimize the two 1-by-2-by-8 pieces to 7 feet, 9 inches prolonged.
6 Then, fasten the two 1-by-2-by-7, 9-inch pieces to the within of every 8 foot stud. Seat the 1-by-2-by-7 foot 9 inch pieces on the plywood. Attach utilizing 1 1/2 inch drywall screws. Screw the 1-by-2-by-7 foot, 9-inch pieces to the 2-by-4-by-8 studs.
7 Use the silicon caulk to seal all the seams in the solar collector container. Enable 24 several hours for the silicon caulk to heal.
8 Paint the interior of the container with the dark paint.
9 Flip the container more than and cut two slots 4 inches broad by 3 feet prolonged the best and bottom edges 3 inches from the best and bottom borders and 1 1/2 inches in from every facet of the plywood. Use a spade tad and drill a pilot hole at every finish of the two slots. Use a jigsaw to cut the 4-inch widths then use a round saw to cut the 3-foot lengths.
10 Minimize a sheet of 3-by-8 foot corrugated steel roofing to 3 foot by 6 feet, 10 inches. Use an abrasive steel-slicing round saw blade to cut the roofing.

Specify a permanent position for your water heater on your roof or another area has a good sun. Using a framework to determine the point pillar of the heater will be screwed to the bearing surface. The roof of the orientation of the surface of the strongest points, read, marks the point and screw drill pilot hole. The screw is assembly framework support surface. Insert the screw hole by vertical base guidance that you just do. Confirm all the screws are rigidly fixed, framework is stable. If you no drilling hole, the framework of drill hole base, through which you can run the upright screw.

Framework installation is reflector surface on how to install solar geyser vacuum tube. Reflector, usually by a stainless steel or other reflective material reflects sunlight to evacuated tube, need to install on the tube. Simple reflective can patches on the manifold. It will remain in the framework. The box vacuum tubes inserted into the frame. Silicon tube silicon grease to prevent scratches, gently insert through the framework of the top and move down, until it is safe to rest on the basis of your frame. Repeat this process as much as possible of evacuated tube heater.

Install valve at the top of the water tank heater. Hot water tank has to be placed in the heating pipe thermo siphon function, the process of heat and less dense water rises instead of cold water, let the water cycle through evacuated tube. Integrated tank framework bolts, and screw bearing surface of the tank chassis. To install a separate tank near the heater of the bearing surface, if the tank is not an integrated type. Confirm the lowest part of the evacuated tube of the tank is higher than the highest point, and the system framework, screws the strongest points of the bearing surface.

Connect the water tank to your vacuum tubes. Run a PVC pipe or hose from your tank at the top of the tube. Run the second tube or hose from the bottom of the tank bottom valve system. Sealed with Teflon tape all connections and according to the need to fill the joint sealant. The cycle will be closed thermo siphon circulation. After reading, I’m sure you have a clear mind about how to install solar geyser vacuum tube.?